www.tantalizetanlounge.com. Pertronix Misfire finally cured. I finally cured my misfire problem and as the thread is so many pages back in this forum, I thought I'd let everyone know what I found out in a new thread. After I rebuilt my 428 and the compression got bumped up a bit due to block deck and cylinder head re-surfacing (plus the over-bore), my engine would misfire. Pertronix ignition installation instructions >> DOWNLOAD Pertronix ignition installation instructions >> READ ONLINE . . . . . . . . . . pertronix. produced by the Flame-Thrower II coil. Since PerTronix cannot test every con guration, the end user must determine what spark plug gap works best for their application. FLAME-THROWER II COIL APPLICATIONS Use with: System Voltage Cylinders Primary Resistance Recommended Flame-Thrower II Coils Black Chrome Epoxy Ignitor II 12V ALL 0.6 ohms 45011.
5. Loosen the coil clamp and remove the existing coil. 6. Install FlameThrower II coil into the coil clamp and tighten into place. Note: If the Flame-Thrower II coil does not fit properly in the existing coil clamp, purchase PerTronix chrome clamp #10002 or zinc clamp #10001. 7.
I then removed the points and condenser, removing the wires back through the distributor wall. Next, I installed the pertronix ignitor II. I started by feeding the wires through the hole in the distributor wall and pushing the rubber seal into place. I ran the wires to the coil (red to positive or "+" and black to negative or "-"). PerTronix HEI イグニッション コイル 商品説明 --- New in Box --- "PerTronix"*Flame -Thrower HEI In-Cap Ignition Coil Fit for : GM. If you want to use an epoxy-filled Pertronix coil for ruggedness (like the MSD 8222) on an 8-cylinder, you could use part numbers 40111 or 45111. They sell for a couple bucks less than the MSD 8222 coil Online. 1966 "C" Code Coupe, Candyapple Red, Pony. Jun 02, 2016 · The Pertronix Ignitor kit comes with all the parts you need. It is suggested that you use the Pertronix Flamethrower coil, but you don’t have to. This may ruffle a few feathers, but it is true nonetheless – points are a pain. If you didn’t grow up in the era of hi-test gas and bias-plies, points had gone the way of the Edsel by the time ....
PERTRONIX PERFORMANCE BRANDS EMISSIONS CODES. This product has been granted a California Air Resources Board (CARB) Executive Order (EO Number) Exemption. It is 50 State Legal when installed on the Specified vehicle per the Manufacturer’s Current Application Guide, the CARB EO, and Installation Instructions. Hello, I just picked up a Ignitor III and Flamethrower III coil for my 70 SS. Looking at the instructions I am stuck on what to do with small resister/condensor on the coil bracket and the condensor in the distributor. I called tech on Friday to make sure I understood. He basically said to ditch. 5. Loosen the coil clamp and remove the existing coil. 6. Install the Flame-Thrower III coil into the coil clamp and tighten into place. Note: If the Flame-Thrower III Coil does not fit properly in the existing coil clamp, purchase PerTronix chrome clamp #5907 or zinc clamp #5906. 7. Connect the wires that were removed from the negative coil.
Someone asked for step by step instructions on installing the Pertronix as a points replacement in an early D-Jet (72,73) , so here goes. Buy a Pertronix 1885 kit. ... just buy a Pertronix 1885 and a Flamethrower coil and install as per the upthread diagram (I am assuming your new coil is same as old Bosch coil, which is not suitable, but other. ..
Stock look distributor features include: * All-new lightweight cast aluminum housing, modeled after the original Delco and Motorcraft distributors. * Hardened gear ground to exact tolerances for precise mesh with cam. * Adjustable vacuum advance canister, providing extra tunability. * Optimized phasing to ensure maximum energy to the spark plug. FlameThrower II Ignition Coil Pertronix 45kv 0.6 Ohms Oil Filled 45011 Ignitor2. FlameThrower II Ignition Coil Pertronix 45kv 0.6 Ohms Oil Filled 45011 Ignitor2. Skip to main content. Shop by category. Shop by category. Enter your search keyword. Advanced: eBay Deals; Find a Store; Help; Sell; Watch.
However, since that time, more than a few people have reported that Pertronix Technical Support has informed them that a ballast resistor was necessary in a 12v 216/235/261 application (with or without their Flamethrower coil ). Just to add to your (and our) confusion, look at page two of these installation >instructions..